RT Journal Article
SR Electronic
T1 An Efficient Ethanol-Vacuum Method for the Decontamination and Restoration of Polypropylene Microfiber N95 Medical Masks & Respirators
JF medRxiv
FD Cold Spring Harbor Laboratory Press
SP 2020.04.12.20059709
DO 10.1101/2020.04.12.20059709
A1 Nazeeri, Albert I.
A1 Hilburn, Isaac A.
A1 Wu, Daw-An
A1 Mohammed, Kabir A.
A1 Badal, D. Yovan
A1 Chan, Moses H.W.
A1 Kirschvink, Joseph L.
YR 2020
UL http://medrxiv.org/content/early/2020/04/16/2020.04.12.20059709.abstract
AB A critical shortage of respirators, masks and other personal protective equipment (PPE) exists across all sectors of society afflicted by the COVID-19 pandemic, placing medical staff and service workers at heightened risk and hampering efforts to reduce transmission rates. Of particular need are the N95 medical face respirators that filter 95% of all airborne particles at and above 0.3 μm in diameter, many of which use meltblown microfibers of charged polypropylene (e.g, the 3M™ 8200). An intensive search is underway to find reliable methods to lengthen the useful life of these normally disposable units.It is currently believed that these masks and respirators cannot be cleaned with 70 to 75% alcohol-water solutions, as past wet/dry experiments show that filtration efficiency can drop by ∼40% after the first such treatment. This has been interpreted as the liquids disrupting the surface charge on the fibers and has led to a recent CDC/NIOSH advisory against using alcohol for their decontamination. We have replicated the drop in efficiency after alcohol treatment. However, we find that the efficiency can be recovered by more effective drying, which we achieve with a vacuum chamber. Drying at pressures of < ∼6 mBar (0.6 kPa) restores the measured filtering efficiency to within 2% or so of the pre-washing value, which we have sustained for 5 cleaning-drying cycles so far in three models of N95 masks. The mechanism seems to be the removal of water molecules adsorbed on the fiber surfaces, a hypothesis which is supported by two independent observations: (A) the filtering efficiency increases non-linearly with the weight loss during drying, and (B) filtration efficiency shows an abrupt recovery as the vacuum pressure drops from 13 to 6 mBar, the range physically attributable to the removal of adsorbed water. These results are not compatible with the electrostatic discharge hypothesis, and rather suggest that water molecules adsorbed to the fiber surface are reducing the filtration efficiency via surface tension interactions (e.g., wicking between the fibers and coating their surfaces with a film).Such a degradation mechanism has two implications: (A) Respirators decontaminated by a soak in 70% v/v ethanol regain their filtration efficiency once they are fully dry. We employ vacuum chambers in this study, which are inexpensive and commonly available. (B) This mechanism presents the possibility that mask filtration performance may be subject to degradation by other sources of moisture, and that the mask would continue to be compromised even if it appears dry. The mask would need to be vacuum-dried to restore its performance.This study introduces a number of methods which could be developed and validated for use in resource-limited settings. As the pandemic spreads to rural areas and developing nations, these would allow for local efforts to decontaminate, restore, monitor, and test medical masks.General Audience Summary The COVID-19 pandemic has created a shortage of masks in hospitals and communities. Inexpensive ways of locally disinfecting and testing masks are of great importance, especially as the pandemic spreads to rural areas and developing nations.We have discovered a method to clean hospital-grade face masks by first soaking masks in an ethanol solution, air-drying them, then vacuum-drying them. Our study has found that this cleaning process can be used on a mask at least five times without altering the filter rate of the mask by more than one per cent. Vacuum-drying the masks removes a thin layer of water that still sticks to the fibers in the mask after air-drying. This layer of water is probably what causes the mask efficiency to drop (that is, how well it filters particles from the air). There is a danger that if the mask gets wet in other ways that it will not filter the air as well. This could also be fixed with the vacuum-drying procedure.Our study may lead to inexpensive designs that would allow hospitals to build their own face-mask testing rigs to measure the filtration efficiency of equipment that they have purchased online from unverified sources as well as those being reused. We built a simple mask testing rig from items that are cheap and easy to obtain, though the current design relies on a calibrated $2,500 laser particle meter. We are working to adapt cheaper laser particle meters into the design.Competing Interest StatementThe authors have declared no competing interest.Funding StatementNo external funding.Author DeclarationsAll relevant ethical guidelines have been followed; any necessary IRB and/or ethics committee approvals have been obtained and details of the IRB/oversight body are included in the manuscript.YesAll necessary patient/participant consent has been obtained and the appropriate institutional forms have been archived.YesI understand that all clinical trials and any other prospective interventional studies must be registered with an ICMJE-approved registry, such as ClinicalTrials.gov. I confirm that any such study reported in the manuscript has been registered and the trial registration ID is provided (note: if posting a prospective study registered retrospectively, please provide a statement in the trial ID field explaining why the study was not registered in advance).YesI have followed all appropriate research reporting guidelines and uploaded the relevant EQUATOR Network research reporting checklist(s) and other pertinent material as supplementary files, if applicable.YesAll data are available upon request.